Panel Builder US

 

By: Andrew Dereka, Product Director at Laird Thermal Systems

Outdoor kiosks have grown in popularity in a wide variety of applications and sectors, including banking, entertainment, retail, showrooms, industrial and education. You see kiosks everywhere, from banks and airports, to theme parks and train stations. Often located outdoors, kiosks and the sensitive electronics they contain are subjected to extreme temperatures, from the cold of winter to the heat of summer. Ambient temperatures can exceed 40°C or below 10°C. Heat loads for the electronics themselves can range from 20 to more than 200 Watts. These extreme temperatures and heat loads can often exceed the operating temperature limits of the sensitive electronics inside, which in turn can affect their functionality and lifespan.

In addition, the demand for higher telecommunication speeds and computing power through 4G/5G networks and always-on broadband services places a huge demand on the kiosk infrastructure. It's the combination of the outdoor environmental conditions and the continuous operating heat load on these systems that result in the generation of a substantial amount of heat within the enclosure. To ensure all-time availability, cooling systems are necessary to protect the electronics inside.

Compressor-based air conditioning systems have traditionally been used for heat removal in outdoor kiosks. However, they can be noisy and occupy a large amount of space. Also, government regulations, particularly in EU, are making it more difficult to specify a solution since ozone depleting refrigerants are being phased out over the next several years. Natural refrigerant alternatives are expensive with limited flexibility to transport via air. Standard air-to-air heat exchangers can be more efficient, but they are often too large to fit inside the kiosk and cool to a few degrees above worst case ambient temperature. This can be a problem for sensitive electronics or batteries with operating temperature limits. 

Cooling systems for use in outdoor kiosks must meet rigorous requirements to withstand outdoor conditions. These requirements might include NEMA 4, humidity and salt spray testing. They may also include more specific issues such as preventing water, dust and wind-driven rain from entering the cooling system. In some cases, the cooling system must provide seismic resistance, corrosion and fire resistance, or shock and vibration resistance. Seals, gaskets, connectors and fans within the cooling system must provide specified NEMA seal ratings. 

Thermoelectric Solutions for Outdoor Kiosks

Thermoelectric cooler assemblies offer an alternative to compressor-based cooling systems for kiosk enclosures. With the ability to cool well below ambient, Thermoelectric cooler assemblies protect electronics inside enclosures from heat, while limiting moisture exposure and other contaminants from the outside environment. 

At their core, thermoelectric coolers use thermoelectric coolers which are solid-state heat pump devices that pump heat via the Peltier effect. During operation, DC current flows through the thermoelectric cooler to create heat transfer and a temperature differential across the module. One side of the thermoelectric cooler is cold, while the other side is hot. A heat absorption and heat dissipation mechanism are connected to the thermoelectric cooler, which are usually heat sinks.  The cold side heat sink absorbs heat from inside the cabinet, while the hot side heat sink rejects heat to ambient environment. The most common type of thermoelectric cooler assembly is an air-to-air configuration. Fans are used to increase the air exchange between hot and cold side to maximize heat transfer.

 

Thermoelectric cooler assemblies offer several advantages over alternate cooling technologies including:

  • Compact form factor
  • Solid-state construction providing robust reliability with few moving parts
  • Ability to heat and cool resulting in precise temperature control
  • Environmentally friendly as no hazardous CFC refrigerants are used

Thermoelectric cooler assemblies are usually mounted on the side of the kiosk enclosure and exhaust the heat load directly to the outside or ambient environment. Thermoelectric cooler assemblies can be used to control temperature of the entire Kiosk or a compartment within the Kiosk where sensitive electronics are located. This requires a smaller thermoelectric cooler assembly solution and reduces the overall unit costs. However, proper ventilation is required to assure the hot side air is getting out to ambient environment.

By reversing the polarity on the thermoelectric cooler, thermoelectric cooler assemblies can heat as well and offer precise temperature control. The ability to heat can be useful in winter time where temperatures can drop below the lower temperature limit of the sensitive electronics or batteries. This also eliminates the need for a resistant heater that would be used in traditional compressor based systems lowering costs.

With fewer moving parts in the system, thermoelectric cooler assemblies offer a lower cost of ownership. Almost no maintenance is required. For areas where a lot of dust occurs, a filter is recommended and on occasion heat sinks should be cleaned with compressed air to remove dust. This assures a more efficient cooling system with long life operation.  
 
Thermoelectric cooler assemblies can maintain temperature between two temperature set points with the use of a bi-directional controller. This controller can turn on the thermoelectric cooler assembly to cool once the upper temperature limit has been reached and turn off a few degrees below the temperature set point. Similarly, the controller can turn on and heat once the low temperature limit has been reached and turn off a few degrees above this limit. A hysteresis setting is used in conjunction with the temperature limit set points to set the desired degrees the thermoelectric cooler assembly will be on during the heating and cooling mode. 

Outdoor Cooler Series from Laird Thermal Systems

Laird AA-230 Series
        Laird Thermal Systems AA-230 Outdoor Cooler Series

Laird Thermal Systems offers the Outdoor Cooler Series, which is a rugged, compact air-to-air thermoelectric cooler assembly product family designed for cooling and heating critical electronics in outdoor kiosks. They run on an open loop at nominal voltages of either 24 or 48 VDC, within a wide operating temperature range from -40°C to +55°C. Cooling capacities range from 100 to 480 Watts and are mountable with appropriately sized hardware. The optional bi-directional controller, SR-54 which cool and heat to specific set point temperatures is sold separately. The fans can be controlled once steady-state is reached to reduce noise. 

Laird AA-250 Series
AA-250 Outdoor Cooler Series

 

The custom-designed heat exchangers use air-ducted shrouds and brand-name fans to further improve energy efficiency. Flexible cold-side air ducts can be oriented in any direction to accommodate obstruction within the kiosk and to maximize circulation.  In addition to the traditional vertical mounting, horizontal mounting is now possible, providing the ability for compartment cooling.

The compact design and optional mounting features allow the thermoelectric cooler assembly to be installed in a specific section of the kiosk to cool vital components or batteries in that compartment. This compartment will need to be thermally insulated to protect against outside temperatures. Keeping the electronics and thermoelectric cooler assembly separated from the rest of the enclosure can reduce the cooling capacity requirements due to lower heat load removal. 

 


Conclusion

The Outdoor Cooler Series does not use compressors or CFC refrigerants, providing environmentally friendly solid-state operation. The solid-state construction offers a cooling solution that requires much less maintenance than compressor-based systems. The heat pumping action is produced by thermoelectric coolers that achieve a high coefficient of performance (COP) to minimize power consumption. The entire product series was designed to pass Telcordia test requirements. 

Cooling and heating of critical electronic components or batteries in outdoor kiosks is necessary to maintain long life operation with almost no maintenance. Thermoelectric cooler assemblies provide a reliable and cost-effective alternative to traditional cooling solutions. They offer a high cooling performance in a compact footprint and are environmentally-friendly, which eases concerns with new government regulations, particularly coming from the EU, regarding removal of ozone depleting refrigerants. 

 

Editor's Pick: Featured Product News


 

Rittal is replacing its previous KS series with the new fibreglass enclosures AX and so completely redefining fibreglass enclosure technology. The development is based on Rittal’s technology for sheet steel and stainless-steel enclosures, which can be used to greatly simplify and speed up manufacturing processes in panel building and switchgear manufacturing. Now, for the first time, fibreglass enclosures also feature this system technology. This is a win-win situation for plant constructors:

Read More

 

 


 

Products for Panel Builders

  • Prev
Bourns, Inc. recently announced the addition of a new model series to its leading  ...
Vishay Intertechnology, Inc. recently introduced a new series of surface-mount AC line rated ...
The newest model of the DXM1200 series wireless controllers maintain the same programming and logic ...
ABB has recently announced the release of ReliaGear LV MCC. The low voltage motor control center is ...
The new CaeBackup/CaeRestore options for B&R's APROL process control system ensure even better ...
binder recently announced an M16 X-coded connector capable of handling the data speeds demanded by ...
binder recently announced the new 818 Series: M8 D-Coded connectors. These will interest engineers ...
SCHURTER announces its new TA36 thermal circuit breaker, improving on an already successful series ...
The new CLICK PLUS PLC series is the next generation of simple control. Building on the practical ...
Littelfuse, Inc. recently launched a new building automation microsite ( ...

Article Feature - Monthly Industry Focus


JAE recently announced the launch of the MX72C / D Series, a squib connector for automotive SRS devices that conforms to the interface standard with omitted shorting bar (shunt-less), and is becoming popular in Europe and the United States.

Recent changes to automotive passenger safety requirements worldwide is serving as a catalyst to an increased level of collision safety performance, especially in Europe and the United States is expected to grow. In addition to the common SRS devices found in a vehicle, new applications such as knee, thorax and pedestrian airbags have begun to trend in an effort to ensure human safety.

Read More


News for Panel Builders

News for Panel Builders
  • Prev
In support of the company’s long-term strategic plan and as the company continues to develop its ...
AVX Corporation has recently joined the South Carolina Manufacturers Alliance (SCMA), the ...
Graybar recently announced several leadership changes, all of which are effective May 1, ...
Supporting its long-term modernization strategy and building on its goal to remain ...
Trace Software International webinars are presented by our experts to provide you best practices in ...
Yokogawa Electric Corporation and Integrated Commissioning and Qualification Consultants, Corp. of ...
Electronic Components Industry Association (ECIA) was recently pleased to announce that ...
nVent Electric plc  recently announced that Greg Scheu has been appointed to its Board of ...
Pilz provides automation solutions for plant and machinery: complete and simple. From sensor ...
TPC Wire & Cable (TPC), a portfolio company of Audax Private Equity, has recently announced ...

Siemens Smart Infrastructure released its new public fast charger Sicharge D for the IEC markets. It is suited for highway and urban fast charging stations, city parking as well as shopping malls and provides one of highest peak efficiencies on the market at 96 percent, scalable charging power and dynamic power sharing.

“With its upgradability and dynamic charging, it is a big step forward to support the future of eMobility. Our customers can be sure to be prepared for future eventualities of eMobility, be it increasing number of required charging options or increasing charging speeds,” said Birgit Dargel, Global Head of Future Grids at Siemens Smart Infrastructure.

Read More


Whether manufacturing packaging machines or components for airliners, companies must be able to guarantee all metal parts will remain durable and dependable throughout the product’s lifecycle. Recognizing this challenge, LSP Technologies pioneered an effective method to increase the strength of metal parts: surface treatment with pulsed laser beams. One of their most recent laser peening systems relies on the flexibility of EtherCAT and PC-based control technology from Beckhoff to meet the most diverse customer requirements.

Read More

 

Selecting a panel meter for a particular application can be a daunting task, given the wide variety of products that are available today. There are many factors to consider when making a decision. Let’s look at a few of the major items.

Function

Panel meters can be categorized by type, size, style or other criteria. One way to begin the selection process is to look at the meter’s function – what measurement is this meter making? Some common functions are ammeter, voltmeter, frequency meter, power meter, energy meter, counter, timer, temperature meter, process meter, and controller.

Read More