The 338 Series Optical Wavelength Meter from Bristol Instruments combines speed and affordability to address the most important requirements of optical transceiver manufacturers. The model 338 has a high measurement rate of 25 Hz that results in reduced testing times and greater production throughput. And, its affordable price point, along with a five-year warranty, provides the lowest cost of ownership compared with similar systems.
RAFI is expanding its rugged RAFIX 22 FSR control component range with a signal lamp featuring a stainless steel collar with IP65, IP67 and IP69 degree of protection to the front side. The integrated red/green LED can indicate three signal statuses. The translucent indicator is a neutral white in standby mode, green indicates regular operating condition, and red signals faults.
SerieFLAT MG-TPMF tags are used for marking cables, conduit, tubes, conductors and components. Presented in stem format, tags are simply snapped off their stems and inserted into the appropriate holders. Consult Cembre for other colours. Compliance is checked by inspection and by rubbing the marking by hand for 15 s with a piece of cloth soaked with water and again for 15 s with a piece of cloth soaked with hexane.
With the motor starters of the MOTUS C14 series from Wöhner, short circuits become less scary. If an error occurs, the electronics switch off the motor within a maximum of 10 microseconds. This means that the MOTUS C14 reacts faster than any fuse and this with a low I2t value. By comparison, the reaction time of a conventional fuse-link is about 2,000 microseconds. With a circuit breaker, the switch-off time in case of a fault is even 5,000 microseconds.
Bel Power Solutions, a Bel group company introduces 100W 4-pair, Power over Ethernet, NBASE-T / 802.3bz Magnetic Modules. The 100W Magnetic Modules are aimed at engineers who are developing products to be compliant with the NBASE-T / IEEE 802.3bz and 802.3bt standards, while optimizing performance and reliability. The 100W 4-pair PoE Magnetic Modules can transmit up to 100W of power, utilizing Ethernet cable that is compatible with the desired bandwidth.
Whether you’re designing an RF Cable Assembly for smaller spaces, high-vibration environments or another challenging application, Molex has the expertise to develop high-quality, custom cable assemblies that ensure reliability and performance. Molex RF connector designs can accommodate standard RG braided cables, micro coax, semi-rigid cable, vendor-specific custom cables, LMR types and hand conformable cable assemblies.
Pepperl+Fuchs is expanding its comprehensive portfolio of identification solutions with the introduction of the IUT-F190-B40 UHF RFID read/write head, which offers an integrated industrial Ethernet interface and REST API. Using these interface technologies, the IUT-F190-B40, which is designed for medium detection ranges, can be quickly and easily integrated into OT and IT systems.
Outstanding performance, low costs, flexible topology and easy handling: these are the advantages of the industrial Ethernet technology, EtherCAT. EtherCAT provides full flexibility: a free topology selection, the possibility of connecting and disconnecting devices and segments during operation, and the performance redundancy of the ring topology. EtherCAT is suitable for both centralized and decentralized architectures, supports Master/Slave, Master/Master, and Slave/Slave communication.
The safe sensorless standstill monitor UG 6946 from the SAFEMASTER S series detects the standstill of 3-phase and 1-phase motors independent of the direction of rotation. This means sensors such as encoders or proximity switches are not required. Access to the danger zone of a system is only possible by the enabling signal of the standstill monitor after the drive has been switched off and run down.
TE Connectivity has launched its Raychem smart RSTI-VS separable connector with voltage sensor, which can be used for grid monitoring and advanced earth fault and short circuit detection in IEC markets. Together with grid monitoring devices such as Kries’ IKI-50, distribution network operators can deploy condition monitoring, advanced fault detection and failure prediction in their networks.
Following the current trend, this space-saving IP 65/67 Industrial PC hardware with flexible mounting options is ideally suited for implementing advanced Industrie 4.0 solutions. A wide variety of onboard interfaces enables the networking of machine or plant sections in the cloud or other networks. Moreover, the integrated EtherCAT P connection offers undreamt-of possibilities for the direct connection of actuators and sensors via EtherCAT P Box modules with IP 67 protection.
In expanding their commitment to providing standard duty connections, Weidmuller was recently proud to announce the addition of a new color-coded Power Distribution Block series to their already impressive selection of IP 20 feed-through terminals. These DIN rail/direct mountable blocks are intended for distributing main power sources for low voltage (600V AC/DC, 30-310A) applications, utilizing large wire sizes, and of course, maintaining finger-safe connections.
Excelitas Technologies Corp. recently announced the LINOS d.fine HR Area Scan Module, which enables area scan applications for the company’s d.fine HR 2.4/128 3.33x High Resolution Inspection Lens. The combination of d.fine HR Lens and new Area Scan Module features a large image circle up to 82 mm and a high resolution up to 300 Lp/mm in a spectral distribution of 400 nm – 750 nm.
New connectors as well as cable-based string fuses extend the SUNCLIX product series for photovoltaic systems from Phoenix Contact. The device connectors are particularly suitable for cabling inverters and string combiner boxes. The fast screw connection saves you time and money during installation. A patented Unlock system enables smaller actual dimensions as well as convenient release without the need for a special tool.
Phoenix Contact’s protective devices in the TERMITRAB complete product family provide a high level of protection against overvoltages in a minimum amount of space. With the TTC-6-1×2-TELE devices, two new product variants are now available for fast VDSL applications with data transmission speeds up to 300 Mbps. The products are specifically tailored to the requirements for data transmission with Super Vectoring.
Stewart Connector, a Bel group company, recently announced the release of their tool-less Cat 6a Cable Splicer. Stewart Connector’s cable splicer is a time-saving solution for Ethernet connections that require field terminations. The cable splicer is designed to create easy connections between patch cables and installation cables for consolidation point applications or for end-to-end links.
