RAFI is expanding its rugged RAFIX 22 FSR control component range with a signal lamp featuring a stainless steel collar with IP65, IP67 and IP69 degree of protection to the front side. The integrated red/green LED can indicate three signal statuses. The translucent indicator is a neutral white in standby mode, green indicates regular operating condition, and red signals faults.
SerieFLAT MG-TPMF tags are used for marking cables, conduit, tubes, conductors and components. Presented in stem format, tags are simply snapped off their stems and inserted into the appropriate holders. Consult Cembre for other colours. Compliance is checked by inspection and by rubbing the marking by hand for 15 s with a piece of cloth soaked with water and again for 15 s with a piece of cloth soaked with hexane.
With the motor starters of the MOTUS C14 series from Wöhner, short circuits become less scary. If an error occurs, the electronics switch off the motor within a maximum of 10 microseconds. This means that the MOTUS C14 reacts faster than any fuse and this with a low I2t value. By comparison, the reaction time of a conventional fuse-link is about 2,000 microseconds. With a circuit breaker, the switch-off time in case of a fault is even 5,000 microseconds.
Bel Power Solutions, a Bel group company introduces 100W 4-pair, Power over Ethernet, NBASE-T / 802.3bz Magnetic Modules. The 100W Magnetic Modules are aimed at engineers who are developing products to be compliant with the NBASE-T / IEEE 802.3bz and 802.3bt standards, while optimizing performance and reliability. The 100W 4-pair PoE Magnetic Modules can transmit up to 100W of power, utilizing Ethernet cable that is compatible with the desired bandwidth.
The safe sensorless standstill monitor UG 6946 from the SAFEMASTER S series detects the standstill of 3-phase and 1-phase motors independent of the direction of rotation. This means sensors such as encoders or proximity switches are not required. Access to the danger zone of a system is only possible by the enabling signal of the standstill monitor after the drive has been switched off and run down.
Following the current trend, this space-saving IP 65/67 Industrial PC hardware with flexible mounting options is ideally suited for implementing advanced Industrie 4.0 solutions. A wide variety of onboard interfaces enables the networking of machine or plant sections in the cloud or other networks. Moreover, the integrated EtherCAT P connection offers undreamt-of possibilities for the direct connection of actuators and sensors via EtherCAT P Box modules with IP 67 protection.
In expanding their commitment to providing standard duty connections, Weidmuller was recently proud to announce the addition of a new color-coded Power Distribution Block series to their already impressive selection of IP 20 feed-through terminals. These DIN rail/direct mountable blocks are intended for distributing main power sources for low voltage (600V AC/DC, 30-310A) applications, utilizing large wire sizes, and of course, maintaining finger-safe connections.
New connectors as well as cable-based string fuses extend the SUNCLIX product series for photovoltaic systems from Phoenix Contact. The device connectors are particularly suitable for cabling inverters and string combiner boxes. The fast screw connection saves you time and money during installation. A patented Unlock system enables smaller actual dimensions as well as convenient release without the need for a special tool.
Stewart Connector, a Bel group company, recently announced the release of their tool-less Cat 6a Cable Splicer. Stewart Connector’s cable splicer is a time-saving solution for Ethernet connections that require field terminations. The cable splicer is designed to create easy connections between patch cables and installation cables for consolidation point applications or for end-to-end links.
SCHURTER’s prominent UMT-H surface mount ceramic fuse family now includes 40 A and 50 A current ratings with an impressive breaking capacity rating of 500 A at 125 VAC / 72 VDC. The series provides unprecedented overcurrent and short circuit protection performance in a package size of 5.3 x 16 mm. The UMT-H was originally developed to provide a smaller alternative to through-hole mounted 5 x 20 mm cartridge fuses, commonly used for primary circuit protection.
The easiest way to control the speed directly on the machine is to use an analog potentiometer. However, wearing gloves in dusty or humid environments, for example, makes operation more difficult. Therefore, the use of the robust SIRIUS ACT ID key-operated switch as a digital potentiometer is particularly suitable under these environmental conditions. This alternative with freely programmable IO-Link electronic module enables precise and fine-grained speed adjustment due to its tactile detent positions.
Littelfuse, Inc. recently launched an industrial manufacturing and processing web page focused on safety. “The new industrial-focused web page puts educational resources at the fingertips of safety and manufacturing professionals,” said Debra Jayson, Senior Marketing Manager, Littelfuse Industrial Business. “Worker safety is a major concern in this industry. This new page provides application information and training materials to help improve electrical safety in key areas such as shock and arc-flash protection.”
SOUTHCO has recently introduced the latest product in its successful line of magnetic catches, with a new version that combines strength and style. Constructed of corrosion resistant stainless steel, the M5 Magnetic Catch combines a highly polished finish with the holding power of rare earth magnets to provide a robust and attractive solution for keeping doors and panels open or closed.
Struggling to have proper heat distribution within your enclosure? Don’t let temperature and condensation derail your mission-critical applications. STEGO is here to help with a wide array of FAN HEATERS that are available in both AC and DC variants. These high-performance heaters are designed to distribute heating power evenly and consistently throughout the whole enclosure. This series of STEGOs heaters are ideal for enclosures where space is at a premium.
Cinch Connectivity Solutions, a Bel group company, now offers a 2.92mm Quick Connect Adapter and High Frequency SMA Quick Connect Adapters, designed to adapt from a standard threaded jack to a Quick Connect Plug. These adapters are designed to allow for rapid test connections to devices using 2.92mm and SMA connectors, resulting in a more efficient testing process by reducing the time and effort required to connect and disconnect the test cable.
The new Power Panel C80 offers the combined advantages of a powerful controller and a modern operator terminal in a single HMI device. The C80 installation is compatible with B&R Automation Panels. Machine builders thus have full flexibility when using the new panel and can scale their machine to meet changing performance and cost requirements. With its low installation depth, the C80 multi-touch HMI is suitable for particularly compact machines where space in the control cabinet is limited.
